Standard Conformity The cameras have been tested in the following conditions:
? Shielded power supply cable
? Camera Link® data transfer cable ref. 14B26-SZLB-500-OLC (3M ? Linear AC-DC power supply
? e2v recommends using the same configuration to ensure the compliance with the following standards 6.1 CE Conformity AViiVA Cameras comply with the requirements of the EMC (European) directive 89/336/CEE (EN 50081-2, EN 61000-6-2). 6.2 FCC Conformity AViiVA Cameras comply with Part 15 of FCC rules. Operation is subject to the following two conditions:
? This device may not cause harmful interference, and
? This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Camera Command and Control Camera configuration is set through the serial interface. Please refer to “Serial Communication” on page 11 for the detailed protocol of the serial line. Note:
1. e2v commends to use E = 1 because of the limited EEPROM write cycles refer on page 12.
2. Camera gain (dB) = G x 0.047. A and B gain value are set in manufacturing but can be adjust if necessary.
3. Commands “H=2” and “H=4” will give 10 and 15 MHz data rate which are not compatible with Camera Link standard. Please don’t use it.
4. The pinout corresponding to this option is fully compatible with the Camera Link standard. Table 7-1. Camera Command and Control Setting Command Parameter Description Configuration record(1) E= 0 1 The camera configuration is recorded on each change The camera configuration is recorded only on request Gain(2) G= 0 to 851 Gain setting from 0 to 40 dB (~0.047dB steps) Even Gain(2) A= 0 to 20 Even pixels gain adjustment (odd – even mismatch adjustment) Odd Gain(2) B= 0 to 20 Odd pixels gain adjustment (odd – even mismatch adjustment) Data transfer(3) H= 0 1 3 5 6 7 8 9 10 Two outputs on external clock One output (multiplexed) on external clock One output (multiplexed) at 20 MHz data rate One output (multiplexed) at 30 MHz data rate Two outputs at 20 MHz data rate One output (multiplexed) at 40 MHz data rate Two outputs at 30 MHz data rate One output (multiplexed) at 60 MHz data rate One output (multiplexed) on external clock (data frequency / 2)(7) Output format(4) S= 0 1 2 12-bit Output data 10-bit Output data 8-bit Output data Pattern(5) T= 0 1 Standard Test pattern Integration Time I= 5 to 13000 Integration time (μs) in free run or external triggered mode Trigger mode M= 1 2 3 4 Free run with integration time setting (see Figure 8-1) External trigger with integration time setting (see Figure 8-2) Trigger and Integration time controlled (see Figure 8-3) Trigger and integration time controlled by two inputs (see Figure 8-4) Even data Offset(6) O= 0 to 15 Even Offset setting from 0 to approx. 200 LSB Odd data Offset(6) P= 0 to 15 Odd Offset setting from 0 to approx. 200 LSB Special commands != 0 1 2 3 4 5 Camera identification readout User camera identification readout Software version readout Camera configuration readout Current camera configuration record Default camera configuration restoration User camera ID $= String of Char. Writing and record of the user camera identification